Subject: [PATCH] net: dsa: mt7530: use resolved link config in mac_link_up()
From: René van Dorst <[email-masked]>
Date: Fri, 27 Mar 2020 15:44:12 +0100

Convert the mt7530 switch driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().

Signed-off-by: René van Dorst <[email-masked]>
Tested-by: Sean Wang <[email-masked]>
Signed-off-by: David S. Miller <[email-masked]>
---

--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -490,17 +490,6 @@ mt7530_mib_reset(struct dsa_switch *ds)
 	mt7530_write(priv, MT7530_MIB_CCR, CCR_MIB_ACTIVATE);
 }
 
-static void
-mt7530_port_set_status(struct mt7530_priv *priv, int port, int enable)
-{
-	u32 mask = PMCR_TX_EN | PMCR_RX_EN | PMCR_FORCE_LNK;
-
-	if (enable)
-		mt7530_set(priv, MT7530_PMCR_P(port), mask);
-	else
-		mt7530_clear(priv, MT7530_PMCR_P(port), mask);
-}
-
 static int mt7530_phy_read(struct dsa_switch *ds, int port, int regnum)
 {
 	struct mt7530_priv *priv = ds->priv;
@@ -674,7 +663,7 @@ mt7530_port_enable(struct dsa_switch *ds
 	priv->ports[port].enable = true;
 	mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
 		   priv->ports[port].pm);
-	mt7530_port_set_status(priv, port, 0);
+	mt7530_clear(priv, MT7530_PMCR_P(port), PMCR_LINK_SETTINGS_MASK);
 
 	mutex_unlock(&priv->reg_mutex);
 
@@ -697,7 +686,7 @@ mt7530_port_disable(struct dsa_switch *d
 	priv->ports[port].enable = false;
 	mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
 		   PCR_MATRIX_CLR);
-	mt7530_port_set_status(priv, port, 0);
+	mt7530_clear(priv, MT7530_PMCR_P(port), PMCR_LINK_SETTINGS_MASK);
 
 	mutex_unlock(&priv->reg_mutex);
 }
@@ -1407,8 +1396,7 @@ static void mt7530_phylink_mac_config(st
 
 	mcr_cur = mt7530_read(priv, MT7530_PMCR_P(port));
 	mcr_new = mcr_cur;
-	mcr_new &= ~(PMCR_FORCE_SPEED_1000 | PMCR_FORCE_SPEED_100 |
-		     PMCR_FORCE_FDX | PMCR_TX_FC_EN | PMCR_RX_FC_EN);
+	mcr_new &= ~PMCR_LINK_SETTINGS_MASK;
 	mcr_new |= PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | PMCR_BACKOFF_EN |
 		   PMCR_BACKPR_EN | PMCR_FORCE_MODE;
 
@@ -1416,26 +1404,6 @@ static void mt7530_phylink_mac_config(st
 	if (port == 5 && dsa_is_user_port(ds, 5))
 		mcr_new |= PMCR_EXT_PHY;
 
-	switch (state->speed) {
-	case SPEED_1000:
-		mcr_new |= PMCR_FORCE_SPEED_1000;
-		if (priv->eee_enable & BIT(port))
-			mcr_new |= PMCR_FORCE_EEE1G;
-		break;
-	case SPEED_100:
-		mcr_new |= PMCR_FORCE_SPEED_100;
-		if (priv->eee_enable & BIT(port))
-			mcr_new |= PMCR_FORCE_EEE100;
-		break;
-	}
-	if (state->duplex == DUPLEX_FULL) {
-		mcr_new |= PMCR_FORCE_FDX;
-		if (state->pause & MLO_PAUSE_TX)
-			mcr_new |= PMCR_TX_FC_EN;
-		if (state->pause & MLO_PAUSE_RX)
-			mcr_new |= PMCR_RX_FC_EN;
-	}
-
 	if (mcr_new != mcr_cur)
 		mt7530_write(priv, MT7530_PMCR_P(port), mcr_new);
 }
@@ -1446,7 +1414,7 @@ static void mt7530_phylink_mac_link_down
 {
 	struct mt7530_priv *priv = ds->priv;
 
-	mt7530_port_set_status(priv, port, 0);
+	mt7530_clear(priv, MT7530_PMCR_P(port), PMCR_LINK_SETTINGS_MASK);
 }
 
 static void mt7530_phylink_mac_link_up(struct dsa_switch *ds, int port,
@@ -1457,8 +1425,31 @@ static void mt7530_phylink_mac_link_up(s
 				       bool tx_pause, bool rx_pause)
 {
 	struct mt7530_priv *priv = ds->priv;
+	u32 mcr;
+
+	mcr = PMCR_RX_EN | PMCR_TX_EN | PMCR_FORCE_LNK;
+
+	switch (speed) {
+	case SPEED_1000:
+		mcr |= PMCR_FORCE_SPEED_1000;
+		if (priv->eee_enable & BIT(port))
+			mcr_new |= PMCR_FORCE_EEE1G;
+		break;
+	case SPEED_100:
+		mcr |= PMCR_FORCE_SPEED_100;
+		if (priv->eee_enable & BIT(port))
+			mcr_new |= PMCR_FORCE_EEE100;
+		break;
+	}
+	if (duplex == DUPLEX_FULL) {
+		mcr |= PMCR_FORCE_FDX;
+		if (tx_pause)
+			mcr |= PMCR_TX_FC_EN;
+		if (rx_pause)
+			mcr |= PMCR_RX_FC_EN;
+	}
 
-	mt7530_port_set_status(priv, port, 1);
+	mt7530_set(priv, MT7530_PMCR_P(port), mcr);
 }
 
 static void mt7530_phylink_validate(struct dsa_switch *ds, int port,
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -222,6 +222,10 @@ enum mt7530_vlan_port_attr {
 #define  PMCR_FORCE_LNK			BIT(0)
 #define  PMCR_SPEED_MASK		(PMCR_FORCE_SPEED_100 | \
 					 PMCR_FORCE_SPEED_1000)
+#define  PMCR_LINK_SETTINGS_MASK	(PMCR_TX_EN | PMCR_FORCE_SPEED_1000 | \
+					 PMCR_RX_EN | PMCR_FORCE_SPEED_100 | \
+					 PMCR_TX_FC_EN | PMCR_RX_FC_EN | \
+					 PMCR_FORCE_FDX | PMCR_FORCE_LNK)
 
 #define MT7530_PMSR_P(x)		(0x3008 + (x) * 0x100)
 #define  PMSR_EEE1G			BIT(7)